Categories

Posts Tagged ‘Sick of Beige’

Sick of Beige basic case v1 (DP5031) back in stock

Thursday, December 5th, 2013

Sick Of Beige basic case v1 (DP5031) is back in stock at Seeed Studio.  A clear laser-cut acrylic project case kit that fits DP5031 PCBs (50mmx31mm) Sick of Beige v1 DP5031 project case is available at Seeed for $3.

Tags: , ,
Posted in News, Sick of Beige | No Comments »

Sick of Beige basic case v1 (DP5031) back in stock

Tuesday, July 16th, 2013

Sick Of Beige basic case v1 (DP5031) is back in stock at Seeed Studio.  A clear laser-cut acrylic project case kit that fits DP5031 PCBs (50mmx31mm) Sick of Beige v1 DP5031 project case is available at Seeed for $3.

Tags: , ,
Posted in News | No Comments »

USB Tester and Sick of Beige

Wednesday, June 19th, 2013

MobileWill shows off his USB Tester in a Sick of Beige (DP5031) case : From the beginning I designed the USB Tester to use the Dangerous Prototype Sick of Beige (SOB) standard PCB sizes. 50x31mm being the smallest rectangle and most ideal for the USB Tester. One of these reasons was...

Tags: ,
Posted in cases, USB | No Comments »

STM32F4 debug board v1.0 Rev2

Thursday, April 18th, 2013

TitanMKD posted an update to his STM32F4 based debug board we covered previously:  This board is intended to be used as a portable multi-purpose debug/hack tool with very fast peripherals and MCU and use standard Dangerous Prototypes Sick Of Beige DP6037 case format A full open source firmware is planned using...

Tags: ,
Posted in hacks, Sick of Beige, tools | No Comments »

Serpac box fits DP5031 with central hole

Thursday, February 7th, 2013

We designed Sick of Beige cases and the accompanying PCB standard sizes because we were sick of plain beige boxes. If you, however, are not sick of them, here is a beige box that fits the DP5031 standard PCB size. It will need an extra central hole in the PCB...

Tags: , ,
Posted in cases | 2 Comments »

PICShift programmable monostable multivibrator

Thursday, January 17th, 2013

Have a race car that needs a monostable multivibrator (one shot pulse) to control the pneumatic gear change actuators? Use a 555 timer, you say? Unfortunately, due to vibrations accompanying race cars a 555 controlled through a potentiometer is out of the question. A solution proposed by the Ohio State...

Tags: , ,
Posted in PIC, Sick of Beige | No Comments »

Raspberry Pi sandwich plate inspired by Sick of Beige

Thursday, January 10th, 2013

Boisblas tweeted a picture of his Raspberry Pi setup, inspired by our Sick of Beige case. The Pi is mounted on a plastic plate with hex standoffs. Like our cases it's not fully enclosed, but it does provide some protection from those pesky shorts when the board is placed on...

Tags: ,
Posted in dev boards | 6 Comments »

Home soldered Sick of Beige compliant Bus Pirate v4

Monday, December 24th, 2012

Some time ago Schazamp made a community order of Sick of Beige compliant Bus Pirate v4. Presslab received his and soldered it up. All that's left is to wait for his Sick of Beige acrylic panels to arrive and assemble the case. I built mine, they look really great. Thanks...

Tags: ,
Posted in BP v4, Bus Pirate | 3 Comments »

Workshop Update for Halloween, October 31st, 2012

Wednesday, October 31st, 2012

We're hard at work editing the Mumbai leg of our Global Geek Tour of India. We'll hopefully get this done on schedule for tomorrow. Today we sent out acrylic case orders to Seeed for all our Sick of Beige standard sizes. Expect them to pop up in a few weeks....

Tags: ,
Posted in Workshop Update | No Comments »

ATX Breakout Board v1.1 Sick of Beige case is available at Seeed

Tuesday, October 30th, 2012

ATX Breakout Board v1.1 Sick of Beige case is available for $4 at Seeed Studio. This case is designed to be simple, cheap, and easy to assemble. The ATX Breakout Board is  sandwiched between two laser-cut acrylic sheets, and the whole assembly is held together with aluminum screws and standoffs....

Tags: , ,
Posted in cases, Sick of Beige | 7 Comments »

STM32F4 Debug Board in a Sick of Beige case

Monday, September 24th, 2012

TitanMKD is designing an STM32F4 based debug board using a DP6037 standard PCB size and a Sick of Beige case.  The board features a Bus Pirate-like serial terminal interface. This board is intended to be used as a portable multi-purpose debug/hack tool with very fast peripherals and MCU and use...

Tags: ,
Posted in Sick of Beige | 1 Comment »

3D Model: Bus Blaster v3 in a Sick of Beige v1 case

Monday, September 17th, 2012

Today's 3D model is the Bus Blaster v3c in our  Sick of Beige v1 enclosure. The Bus Blaster is a high-speed JTAG debugger for ARM processors, FPGAs, CPLDs, flash, and more. The v3 is a PCB, and part placement change only. The electrical connections are identical to the Bus Blaster...

Tags: , ,
Posted in 3D Model, Bus Blaster | 1 Comment »

Sick of Beige v1 DP5031 case available at Seeed

Wednesday, September 12th, 2012

A clear laser-cut acrylic project case kit that fits Sick of Beige DP5031 PCBs (50mmx31mm) is now available at Seeed for $3. We're adding case sizes as you ask for them, so if you'd like a specific one please give us a shout. Protect your project from electrical shorts and...

Tags: , ,
Posted in cases, releases, Sick of Beige | 11 Comments »

3D model: Sick of Beige v1 template design

Monday, September 10th, 2012

Sick of Beige v1 DP5031 cases are done, so we needed a generic image for the sales page. Today's rendering is an image of a DP9056 standard size to use at Seeed. The basic case is simple, cheap, easy to assemble, and fits our Sick of Beige standard PCB sizes. Check...

Tags: ,
Posted in 3D Model, Sick of Beige | No Comments »

Customized Sick of Beige case built

Wednesday, September 5th, 2012

Riktw designed a case for his CMSIS-DAP ARM debugger based on our Sick of Beige templates, and standard PCB footprints for eagle. You can find his laser cutting design files in the forum. I also made a small casing for my PCB, first time ever I used Sketchup, think it...

Tags: ,
Posted in cases, Sick of Beige | 1 Comment »

Intervalometer turns on the air conditioning at night automatically

Friday, August 17th, 2012

Matseng designed an IR remote control intervalometer. He got tired of waking up and turning on his air conditioner during the night, so he built a project to do it for him. The device sends on/off IR codes to the air conditioner, controlling it at set intervals. He designed it on...

Tags: , , ,
Posted in project logs, Sick of Beige | 3 Comments »

3D Model: ATX Breakout Board v1.1 Sick of Beige case

Monday, August 13th, 2012

Today's 3D model is the Sick of Beige case for the ATX Breakout Board v1.1. This board recycles an old computer PSU into a handy bench tool with 3.3/5/12/-12 volt supplies. The case uses  8x8mm standoffs and some bolts to hold together the 2 laser cut acrylic sheets. Expect it...

Tags: , ,
Posted in 3D Model, cases, Sick of Beige | 3 Comments »

Another Sick of Beige case design

Monday, August 13th, 2012

Systemstech submitted a Bus Pirate v3.6 Sick of Beige design. His design has the board mounted on an inner ring with mounting holes, with the other sheets glued together. All the layers are welded with solvent but for the last two the makeup the bottom lid and those two are...

Tags: ,
Posted in BP v3, cases, Sick of Beige | No Comments »

Workshop Update for July 26th, 2012

Thursday, July 26th, 2012

Releasing the Sick of Beige standard PCB template and cases dominated the day. We made a video about it, showed off the standard PCB library, and presented the two initial SoB v1 case designs. As a demo project for the Sick of Beige cases, toady we designed 2 protoboards on...

Tags: , ,
Posted in Sick of Beige, Workshop Update | No Comments »

WORKSHOP VIDEO #31: Sick of Beige standard PCB templates and cases

Thursday, July 26th, 2012

[embed]http://www.youtube.com/watch?v=x_3jcsEbFWg[/embed] Are you sick of beige project boxes that hide your cool board and hard work? Wouldn't it be cool if your project was case ready from the first revision? Sick of Beige cases are simple protectors and enclosures for hobby electronics project. Design your project with our standard PCB...

Tags: ,
Posted in Videos | 26 Comments »

Next Page »

Recent Comments

  • DP.: fixed, thanks
  • Bovine: Title of article has the wrong number for ESP8266 typed.
  • burkm m: It drifting even further using that standard XO...
  • langwadt: a HC14 is a bad choice for an xtal oscillator, the unbuffered non-Schmitt trigger HCU04 is much better for that application
  • Bill F: I'm ready for one!