Sick of Beige v1 DP5031 case available at Seeed

Posted on Wednesday, September 12th, 2012 in cases, releases, Sick of Beige by DP

A clear laser-cut acrylic project case kit that fits Sick of Beige DP5031 PCBs (50mmx31mm) is now available at Seeed for $3. We’re adding case sizes as you ask for them, so if you’d like a specific one please give us a shout.

Protect your project from electrical shorts and fingers, but keep it accessible for hacking and showing off.

Sick of Beige basic case v1 is designed to be simple, cheap, and easy to assemble. The project PCB is sandwiched between two laser cut acrylic sheets, and the whole assembly is held together with aluminum screws and standoffs.

It’s easy to get your project to fit the case. Drop a PCB footprint on your Eagle schematic, and then route your project on the board template. KiCAD footprints coming soon!

Sick of Beige v1 DP5031 project case is available at Seeed for $3.

This entry was posted on Wednesday, September 12th, 2012 at 1:00 pm and is filed under cases, releases, Sick of Beige. You can follow any responses to this entry through the RSS 2.0 feed. You can skip to the end and leave a response. Pinging is currently not allowed.

11 Responses to “Sick of Beige v1 DP5031 case available at Seeed”

  1. bzorg says:

    I have done one myself a few month ago for my ATX breakout board

  2. Matseng says:

    Hey Ian, can you get Seeed to stock the screw/distances set as well so we can make customized cutout SOBs and still get a “DP” look&feel of it?

    Or is it possible to puchase 5 pcs of the standard SOB and then pay Seed the regular $7.50 laser cutting fee to customize them?

    • Ian says:

      I will check on the hex standoff set. This is something I hope to put together personally in China shortly, along with a DP parts kit.

      I imagine it is way easier for them to put your order in a bulk cut job than customize an existing slab, but my experience laser cutting includes seeing Seeed’s machine and… :)

  3. David Croft says:

    I would like to see a DP5050 case please, I use this size for most of my PCBs as it fits the lowest band of PCB size at both ITead and Seeed.

  4. M H says:

    Doesn’t this pose a static risk for electronics?

    Acrylic is one of the materials used in demonstrating generation of static electricity.
    Is this specially treated in some way to prevent static buildup?
    Does it just rely on nobody ever touching the case and the electronics at the same time.


    • Ian says:

      You’re right, it is a weakness in the concept. It is a very common case type though, used by 1000s of hobbyists and even by big dev board makers. Problem don’t seem to be widespread, but I will keep an eye out for higher failure rates in cased projects.

  5. Filip says:

    It’s not treated in any way. The case does enclose the electronics on the inside of it, so touching them would be rather difficult. The only problem I see is if someone touches exposed pins in the headers

  6. Bjarke says:

    KiCAD footprints coming soon

  7. Bjarke says:

    Cool – Thank you very much! SoB is a fantastic initiative – one could wonder why nobody came up with this idea several decades earlier!?


Leave a Reply

Notify me of followup comments via e-mail. You can also subscribe without commenting.

Recent Comments

  • Nathan Johnson: 100 channels. Not many are legal in any given area. Be sure to comply with local laws.
  • William Brodie-Tyrrell: It's getting to the point where it's cheaper and definitely easier to use a Pi Zero or similar and a $20 3G USB dongle. Power...
  • KH: IIRC most of the actual operating system of modern HDDs is in one of the platter(s); the stuff on the 25VF010 is a bootup firmware......
  • Trev: I don't know of any inexpensive 3G modules (prices start around $US 50), but it does explain why 2G modules are relatively inexpensive by comparison....
  • Zonie: This site Rocks!