SQUIX ESP8266 based e-paper WiFi weather station

Erich Styger documented his experience building Daniel Eichhorn’s e-paper weather station with a custom enclosure: Using e-paper for a weather station is an ideal solution, as the data does not need to be updated often. By default, the station reaches out every 20 minutes for new data over WiFi and then updates the display. Daniel […]

WiFi TFT touch LCD weather station with ESP8266

Erich Styger built this ESP8266 WiFi weather station with touch LCD and wrote a post on his blog detailing its assembly: After the “WiFi OLED Mini Weather Station with ESP8266“, here is another one: this time with Touch LCD :-)  In the previous article (“WiFi OLED Mini Weather Station with ESP8266“) I have used the […]

Pulsecounting and deepsleep based IoT water meter

Tisham Dhar has written an article detailing his pulsecounting and deepsleep based IoT water meter project: I admit to being a tiny bit obsessed with monitoring utility bills and gathering data on my usage patterns blow-by-blow. The energy monitoring has reduced my electricity bills, so I wanted to have a go at the water usage. […]

Bridge monitoring system using wireless sensor network

Zx Lee and his friends built the bridge monitoring system using wireless sensor network, that is available at github: Recently, I completed a mini project together with two of my friends. So I am going to take this opportunity to share the project that we have made, we named it the Bridge Monitoring System (BMS) […]

Magic Mote MSP430G2553 wireless sensor node with NRF24L01+ module

Tom from Magic Smoke writes: This is my first time designing a PCB for MSP430. I really like the NRF24L01+ booster pack but I would like something smaller to use for remote temperature sensors. With that in mind I’ve designed a 24.5 x 50 mm PCB (2 on a 5×5 cm prototype) featuring MSP430G2553 and […]

EasyESP-1: a rapid prototyping and development board for ESP8266

Raj over at Embedded Lab has designed a development board for ESP8266: EasyESP-1 is a rapid prototyping board for the low-cost, WiFi-enabled ESP8266 microcontroller. With an onboard USB-to-Serial converter pre-installed, EasyESP-1 does not require any additional hardware to download your application firmware to the ESP8266 chip. The ESP module used in this development board is […]

DIY IKEA wireless Qi charging for the Hexiwear

Erich Styger built a DIY a wireless charging system for the Hexiwear: The Achilles Heel of the Mikroelektronika Hexiwear is its charging: the charging and USB connector are only designed for a limited number of plug-unplug cycles, and it does not have a wireless charging capability like the Apple iWatch. Until now! I have built […]

HC-12 433MHz wireless serial communication module configuration

Dziku  writes: HC-12 are cheap 433MHz wireless serial port communication modules with a range up to 1800m in open space. Each costs about $5 when bought from China, and 2 of them can create wireless UART link that can be used, for example, to transfer telemetry data from UAV. Or drive IoT device. Or connect […]

Wifi enabled 8×64 pixel LED matrix display

Raj over at Embedded Lab has just finished a new project article about Wifi-enabled LED matrix display using ESP8266: This project is a modification of my previous Bluetooth-enabled LED matrix display project, which used 8×64 monochromatic LED matrix (total 512 LEDs) for displaying scrolling text message. The original project used Bluetooth for display data transfer […]

New ESP8266 board

M0xpd writes: You can well see it is an engineering sample, because I’m squeezing the wrong size packages into locations (quarter Watt resistors where eighth Watt components should be, etc) and using a mishmash of different component types, but you’ll forgive me, I’m sure. The new design presents the Expressif ESP8266 device on an Arduino-sized […]

LoRaWAN FeatherWing for Adafruit Feather

  Dan Watson documented a new custom FeatherWing he has designed to add the MicroChip RN2483/RN2903 LoRaWAN module to Adafruit Feather: I have designed some FeatherWings in the past to add a LoRa transceiver module to Feather. I did the LoRa FeatherWing Development Breakout and the LoRa FeatherWing IOX that used the HopeRF RFM95/96(W) modules. […]

WiFiRGB – A WiFi-enabled RGB high-power LED

Tom blogged about his WiFi/Browser controlled RGB LED project: Features Simple hardware, using pre-fabricated modules Controls an RGB LED via any recent browser, any operating system WiFi credentials can be configured via browser Software is written as an Arduino sketch Full details at Tom’s blog. Check out the video after the break.

How to build a control circuit with adjustable working time via wi-fi

Yahya Tawil over at All About Circuits posted a detailed how-to on building a control circuit with adjustable working time via Wi-Fi: In this article, you’ll learn how to build a system that can turn DC loads on and off using a mobile application. You’ll also learn how to perform this task via immediate actions or via […]