OLS software Java 7 doesn't work

[ppatierno]

Hello,
I have downloaded OLS software from this link http://gadgetfactory.net/logicsniffer/i ... r.Download (Windows Expert version without JRE because I have already installed Java 7 on my PC).
When I try to start the application with Jawis-OLS-client.exe, nothing appens. If I execute run.bat under jawis-ols-client folder, I see a lot of exception on bundles....Using Java 6, the client works fine !
Is there any known problem with Java 7 ?

Thanks,
Paolo.

[ppatierno]

I have downloaded the OLS software from the following link http://www.lxtreme.nl/ols (version 0.9.6.1) and it works with Java 7 but it have a little different UI. What is the differences between the two versions I have downloaded ?

Thanks,
Paolo.

[jawi]

The 0.9.6 release was mostly about the new signal view/ui. The version from GadgetFactory is old and merely provided for convenience. But, the official releases can always be found on http://ols.lxtreme.nl/.

[MickM]

Hi;
I finally got it working using the information here:
https://sites.google.com/site/easylinuxtipsproject/java

Very nice Jawi!

Mick M

[MickM]

Hi Tayken;
Thanks! - you fixed it.

Erase the PIC:
[mick@localhost pk2cmdv1-20Linux2-6]$ ./pk2cmd /PPIC24FJ256GB106 -E

Program the Bootloader:
[mick@localhost pk2cmdv1-20Linux2-6]$ ./pk2cmd /PPIC24FJ256GB106 -MP -FBPv4-bootloader-v1.hex

Program the PIC:
[root@localhost BPv4-firmware]# ./pirate-loader_lnx --dev=/dev/ttyACM0 --hex=BPv4-firmware-v6.2-r1981.hex

Check it out:
[mick@localhost pk2cmdv1-20Linux2-6]$ su -
[mick@localhost pk2cmdv1-20Linux2-6]$ screen /dev/ttyACM0 115200
HiZ>i
Bus Pirate v4
Firmware v6.2-beta1 r1981
DEVID:0x1019 REVID:0x0003 (24FJ256GB106 A5)
http://dangerousprototypes.com

The Mode LED never did come on at all.
There is no voltage on either side of R5.
My probe is too fat to try and probe the PIC
R3 has 3.3 and 1.78V for the Power LED.

I have tried the PGC-PGD jumper, and the $ command.

There is a strange phenomenon.
If I run as Mick Screen comes back instantly.
If I run sudo it works, but I get phantom keystrokes to the BP.
If I run as root with su - , then all is ok.

I have tried various USB cables, no change.

~ Self Test:
Disconnect any devices
Connect (ADC to +3.3V)
Space to continue
Ctrl
AUX OK
MODE LED OK
PULLUP H OK
PULLUP L OK
VREG OK
EEPROM
SCL OK
SDA OK
WP OK
READ&WRITE OK
ADC and supply
Vusb(4.89) OK
5V(4.85) OK
5V VPU(4.58) OK
ADC(3.31) OK
3.3V(3.41) OK
3.3V VPU(3.16) OK
Bus high
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z 0
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z 1
MOSI OK
CLK OK
MISO OK
CS OK
MODE, VREG, and USB LEDs should be on!
Any key to exit

All LEDS are in fact ON.


Again Thanks Tayken!!!

It's now 5:30 AM Bye.

Mick M