Re: 900M/T12/JBC + heat gun soldering controller Reply #30 – March 18, 2017, 01:30:16 pm ... Last Edit: January 19, 2019, 04:56:25 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #31 – March 28, 2017, 04:00:41 pm ... Last Edit: January 19, 2019, 04:56:43 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #32 – April 06, 2017, 08:05:29 pm ... Last Edit: January 19, 2019, 04:57:01 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #33 – April 10, 2017, 01:08:54 pm ... Last Edit: January 19, 2019, 04:57:19 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #34 – April 24, 2017, 03:00:39 pm ... Last Edit: January 19, 2019, 04:57:35 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #35 – April 27, 2017, 10:32:25 pm Hello projector 42, I purchased display http://https://ru.aliexpress.com/item/2PCS-0-96-inch-White-Color-128X64-OLED-Display-Module-For-Arduino-SSD1306-Driver-Chip-I2C/32797170982.html?spm=2114.03010208.3.309.cj9x9N&ws_ab_test=searchweb0_0,searchweb201602_2_10065_10068_433_434_10136_10137_10138_10060_10062_10056_10055_10054_302_10059_10099_10103_10102_10096_10052_10053_10050_10107_10051_10106_10084_10117_10083_10119_10080_10082_10081_10110_10111_10112_10113_10114_10078_10079_10073_10070_10122_10123_10120_10126_6000000_10127_10124_10125,searchweb201603_1,afswitch_1_afChannel,ppcSwitch_7,single_sort_0_default&btsid=4982e2c6-fc95-4e32-8609-ba86a842a91e&algo_expid=a62e4c0a-f5c6-46d8-a7da-c5173458c2f6-36&algo_pvid=a62e4c0a-f5c6-46d8-a7da-c5173458c2f6 But its i2c scanner is located at the address 0x3C (Arduino checked). Can I do something about this? Last Edit: January 01, 1970, 01:00:00 am by Guest
Re: 900M/T12/JBC + heat gun soldering controller Reply #36 – April 28, 2017, 08:28:59 am ... Last Edit: January 19, 2019, 04:57:51 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #37 – April 28, 2017, 08:54:06 am Firmware from this post: viewtopic.php?f=56&t=8494&start=15#p65885Display connected like this:GND -GNDVCC - +5VSCL - PA5SDA - PA6Result - black screen0x3C (7-bit address) Checked the working capacity of the display on Arduino, I'm not a programmer, otherwise I did not come up withChecked by this instruction: http://www.instructables.com/id/Monochr ... ino-SSD13/The display is working Last Edit: January 01, 1970, 01:00:00 am by Guest
Re: 900M/T12/JBC + heat gun soldering controller Reply #38 – April 28, 2017, 09:52:00 am ... Last Edit: January 19, 2019, 04:58:05 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #39 – April 28, 2017, 10:52:43 am Reduced the length of the wires to 4cm, added pull-up resistors 4.7k. Result - there is no image Last Edit: January 01, 1970, 01:00:00 am by Guest
Re: 900M/T12/JBC + heat gun soldering controller Reply #40 – April 30, 2017, 03:31:40 pm ... Last Edit: January 19, 2019, 04:58:20 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #41 – May 02, 2017, 12:18:10 pm All works, hurray! Many thanks for the help, the problem is solved, increased C10 (reset mcu) to 4.7uF Last Edit: January 01, 1970, 01:00:00 am by Guest
Re: 900M/T12/JBC + heat gun soldering controller Reply #42 – May 08, 2017, 06:09:19 pm ... Last Edit: January 19, 2019, 04:58:38 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #43 – May 08, 2017, 06:22:03 pm ... Last Edit: January 19, 2019, 04:58:56 pm by projector42
Re: 900M/T12/JBC + heat gun soldering controller Reply #44 – July 10, 2017, 02:59:23 pm ... Last Edit: January 19, 2019, 04:59:14 pm by projector42