Show Posts - ronald

This section allows you to view all Messages made by this member. Note that you can only see Messages made in areas you currently have access to.

Messages - ronald

Web platform / Re: Webplatform Contiki 2.5 port

August 31, 2013, 10:57:24 pm

Guys, could someone please tell where this "https://github.com/shuckc/contiki-mirror" this lives now or where I could pull a copy? I'm getting a 404 on github for the original link.

Thanks

Open Bench Logic Sniffer / Re: OBLS update not working, ACT not lit

January 11, 2012, 04:12:54 pm

Hi Ian,

That worked for me ( shorting the pins, etc ) and I was able to recover.

Afterwards I did the same firmware upgrade steps and selections that killed my
OLS earlier and finished the whole thing without any problems this time.

Thanks!

Open Bench Logic Sniffer / Re: OBLS update not working, ACT not lit

January 11, 2012, 10:34:36 am

My problem is somewhat similar to dion so I have decided to add to this thread instead of creating a new one. I hope that is ok.

So to start my upgrade attempt, I loaded up the client, and did a capture run. All went well, I recorded the active port as COM89.

I then went on to run the Upgrade script, specifying the com port and pressing Upgrade+Reset which lit up both LEDs. After confirming that, the upgrade script opened a cmd window that showed it proceeding with an update. That also went well and i recall seeing something about entering or starting the bootloader. I next selected logic_sniffer_3.07-Demon-Core.bit" and "OLSv1.firmware.v3.0.hex" when asked and confirmed.
A new window was opened which had an "HID buffer" error then the upgrade terminated.

Sorry for the non-exact error, I have upgraded my board previously without issues and so was caught not paying attention.

At this point, the OLS is no longer being detected when you plug into into a USB port. The power LED is ON but depressing Update and then clicking Reset does nothing, tho just clicking Reset does light up the ARM led on other side of the board.

This line was also in the upgrader log file -
[11/01/2012 16:39:09] !!! Err: LastError = 1167 File: .pic_bootloader.cpp, Line: 673

Does this mean that the bootloader is gone?

I see that there is a serial port header beside the USB connector, can i use this in place of the USB and any chance it is 5v+ friendly ?

What would be the best way to proceed? I have access only to a pickit2.

TIA

Bus Pirate Support / Frequency counter

June 06, 2010, 06:43:01 pm

Hello,

I just tried the frequency counter function on my board and found that I could not get a reading
on anything lower than 256Hz (lower frequencies just returns 0Hz). This is on a v3 board that
had been upgraded to 4.1.

Anyone having the same issue with their unit? I could not find any related issues on the forum so
it might just be me.

Thanks
Ronald

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#	Time	Memory	Function	Location
1	0.0125	2300952	session_write_close ( )	...(null):0
2	0.0128	2432544	ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )	...(null):0
3	0.0128	2433320	Database_MySQL->query( )	.../DatabaseHandler.php:119
4	0.0556	2572056	Database_MySQL->error( )	.../Db-mysql.class.php:273