1
Bus Pirate Support / Re: Buspirate v3 VS v4
Any idea when these might be available?
Messages
This section allows you to view all Messages made by this member. Note that you can only see Messages made in areas you currently have access to.
Messages - s7726
Any idea when these might be available?
2
Project development, ideas, and suggestions / Re: Dangerous Soldering Iron driver V1.5(based on Arhi's gen
3
Project development, ideas, and suggestions / Re: Dangerous Soldering Iron driver V1.5(based on Arhi's gen
for the big one find one that gives you enough current and is higher then 300uH
for the small one (1uH) you can omit it (just put a wire across it to allow current to flow)[/quote]
When you say "gives enough current" do you mean can handle the current? I used the spec'd part from the list for that one.
Is there something I should look for, for maybe needing the 1uH? Will I maybe see some noise or ripple that it would alleviate?
4
Project development, ideas, and suggestions / Re: Dangerous Soldering Iron driver V1.5(based on Arhi's gen
A few things, mostly on packages that may have just been specified too far
Code: [Select]
D1 1 1N4148DO35-7 DO35-7The 7 and 7.6 part threw me.
D2,D3,D4,D5,D6 5 1N4003 DO41-7.6
D8 1 1N5819 DO41-7.6
Code: [Select]
IC2 1 LM385Z TO92I ended up finding 926-LM336BZ-5.0/NOPB that seemed compatible
Code: [Select]
L1 1 MICC10 MICC10I couldn't find an MICC10 but looking through the other blog from Arhi I think I came up with something reasonable 542-78F1R0-RC
Code: [Select]
Part Quantity Value Package Qty MouserThe last ones i think I found something that will work for all of them.
T1 1 BJT NPN TO92-CBE 1 512-BC33725BU
T2 1 BJT PNP TO92-EBC 1 512-KSA733CGBU
TRIAC 1 TIC206D TO220BV 1 576-Q4004L3
XTAL1 1 20Mhz HC49U70 1 774-ATS20A
5
Project logs / Re: HAKKO (907ESD) and SOLOMON (SL-10/30) soldering iron dri
Re posted in the DSID v1.5 topic.
6
Project development, ideas, and suggestions / Re: Dangerous Soldering Iron driver V1.5(based on Arhi's gen
I just ordered the DP v1.5 SID and I've been looking over the Parts List. It's not exactly clear on some things but I did the best I could to find the appropriate parts.
If someone gets a chance could you look this over? I would like to get it nailed down and make it available to others in place of the existing list.
I ended up looking on mouser. I went with 1% for alot of the resistors because they were cheap anyway. For the Headers I just tacked on a strip of 36 SIL for each line item (You can never have too many). I plan to use 2xSIL out of the extras for the DIL. This might be something to change for throwing it out to the masses.
7
Project logs / Re: HAKKO (907ESD) and SOLOMON (SL-10/30) soldering iron dri
I just ordered the DP v1.5 SID and I've been looking over the Parts List. It's not exactly clear on some things but I did the best I could to find the appropriate parts.
If someone gets a chance could you look this over? I would like to get it nailed down and make it available to others in place of the existing list.
I ended up looking on mouser. I went with 1% for alot of the resistors because they were cheap anyway. For the Headers I just tacked on a strip of 36 SIL for each line item (You can never have too many). I plan to use 2xSIL out of the extras for the DIL. This might be something to change for throwing it out to the masses.
-Gavin
PS Thanks again Lynn!