Skip to main content ↑ ↓

Topics

This section allows you to view all Topics made by this member. Note that you can only see Topics made in areas you currently have access to.

Topics - PureBluff

1
CPLD programmable logic / xsvf player issues in Win7 x64
Hi all,

Recently upgraded my laptop to  HP Probook 6560b (Win7 x64)

Now my buspirate / xsvf player doesnt work :( It plays the first 4096 bytes, reports success and error free but obviously it's not fully programmed the CPLD logic board.

Is there a known issue regarding x64, as it still works on my old x86 install on my old laptop. I don't have a log to hand, but will reply/edit later with one once I hook it up. Obviously the BP is detected fine/on said comport for it to play the first part, but don't know where to start with it for diagnosing issues.

Any input greatly appreciated.

Regards

**EDIT**

Here is the log,

Quote
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation.  All rights reserved.

C:UsersBluffer>cd Downloads

C:UsersBlufferDownloads>cd BPv3.XSVFplayer.v1.1

C:UsersBlufferDownloadsBPv3.XSVFplayer.v1.1>BPXSVFplayer.exe -p com4 -f c:rev2e.xsvf
-----------------------------------------------------------------------------

 BusPirate XSVF Player V.01
 http://www.dangerousprototypes.com

-----------------------------------------------------------------------------
File is 22846 bytes, read 22846 bytes Opening Bus Pirate on com4 at 115200bps, u
sing XSVF file c:rev2e.xsvf
 Entering XSVF Player Mode
 Waiting for first data request...ok
Sending 4096 Bytes (1000)...ok
End of operation reply 00
  Success!
 Thank you for Playing! :-)
2
Bus Pirate Support / XSVF_ERROR_MAXRETRIES | Insight ?
While probably not the most intuitive title, I figured it might get anyone who has seen the error to look in and advise.

I just tried programming a CPLD (XC2C64A) with my BusPirate and PigTail wire.

It's correctly hooked up, I've triple checked.

I get this error, I'm not sure if I have previously programmed this board, it was attached to my Bus Pirate when I started this project.

Code: [Select]
c:UsersBlufferDownloadsBPv3.XSVFplayer.v1.1>BPXSVFplayer.exe -p com3 -f c:project1.xsvf
-----------------------------------------------------------------------------

 BusPirate XSVF Player V.01
 http://www.dangerousprototypes.com

-----------------------------------------------------------------------------
File is 22812 bytes, read 22812 bytes Opening Bus Pirate on com3 at 115200bps, u
sing XSVF file c:project1.xsvf
 Entering XSVF Player Mode
 Waiting for first data request...ok
End of operation reply 03
  Device did not respond: XSVF_ERROR_MAXRETRIES
 Thank you for Playing! :-)

Obviously, not knowing just what the error means (google doesnt throw up much) I don't know if it is in fact an issue with my BP (probably not) but I figured someone may be able to help.

Best Reagrds
3
CPLD programmable logic / CoolRunner-II (xc2c64a) XSVF / BusPirate Issues.
Hi all,

Just got my Bus Pirate today.

It's a sparkfun one but it seems to have com with 4.x bootloader as ds30 loader connected fine but PIC24F wouldn't.

With this in mind, I flashed bpv3-xsvf-vb to it, removed the jumper and cycled the usb power to the device.

I then created my .xsvf in Xilinx Lab-Tools.

I wired up my BusPirate to the CoolRunner-II using this install which I believe to be correct ?

[link] i. imgur . com / XjRlQl . png

I then use the command;

bpxsvfplayer -p com14 -f filepath.xsvf

To which I get the following output.

Quote
BusPirate XSVF Player V.01
-----------------------------------------------------------------------------
File is 22846 bytes, read 22846 bytes Opening Bus Pirate on com3 at 115200bps, u
sing XSVF file xc2cprog.xsvf
 Entering XSVF Player Mode
 Waiting for first data request...ok
Sending 4096 Bytes (1000)...ok
End of operation reply 02
  Device did not respond as expected: XSVF_ERROR_TDOMISMATCH
 Thank you for Playing! :-)

Can anyone see any glaringly obvious mistakes ? Something I as a noob have overlooked? Or misunderstood?

If not, does anyone have any suggestions?

Running WinXP SP2 (x86) if it matters, USB2Serial drivers are installed.

Many thanks for looking

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#TimeMemoryFunctionLocation
10.01222294440session_write_close ( )...(null):0
20.01252426032ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )...(null):0
30.01252426808Database_MySQL->query( ).../DatabaseHandler.php:119
40.05622565544Database_MySQL->error( ).../Db-mysql.class.php:273