Skip to main content ↑ ↓

Show Posts

This section allows you to view all Show Posts made by this member. Note that you can only see Show Posts made in areas you currently have access to.

Messages - WerVa

4
Project logs / Re: Really universal soldering controller
Quote from: tronix on

https://imgur.com/a/f21VxsF


You have the newest firmware?

I see that if you have not connected, you have ACE status

I have ACQ


 #3179
ACF/DCF - FULL POWER  (JBC C245 120W).
ACH/DCH - 1/2 POWER (JBC C210 40W).
ACQ / DCQ - 1/4 POWER  (JBC ะก105 / C115 14W).


#3775
- 1/8 power (JBC Nano now works even better) - shows "ACE" or "DCE" on main screen when in use


Ok that mean that i have old version from release not from folder UniSolder-5.2/software/front/US_Firmware.X/dist/PIC32_Standalone/production/
I'll check by evening, My was from (06.2020)
6
Project logs / Re: Really universal soldering controller
Quote from: tronix on
You are correct it should be empty on JCB245 or any other solder iron, most probably have more problems sorry does the JBC245  work at least? if not I would check the wiring for the JBC245.



I waiting for tip. But connection should be fine
RED: Vout1- and SENSEA
GREEN: EARTH and SEANSEB
BLUE: Vout+


Edit: When i connected only resistor the same: power bar is full but 0W , anyone have idea?
12
Project logs / Re: Really universal soldering controller
Is probably U6 On IN i have 3.2V and on OUT i have 3.2V ...

[quote ]
The power supply at the MCU pins should be 3.3V, and the reference should be 3.0V. Then, on C210, when no cartridge is connected, the SENSEA should be around 1.5 - 2V, far beyond the threshold of full ADC 1023 digits after the amplification.
[/quote]

On C210 SENSEA i have 1.1V @sparkybg you think when i replace U6 that should be fine?

Can i use for U6: REF3130AIDBZT ?
13
Project logs / Re: Really universal soldering controller
Quote from: sparkybg on
if it shows 511, then something is wrong with signal path or reference. In order for MCU to detect "sensor open/no instrument" condition, the ADC should go to it's maximum value of 1023. 511 on screen means that it does not go to 1023, but to a value less than this. This means that either the current sources, the amplifiers, the reference, or the power supply is not functioning properly.

The power supply at the MCU pins should be 3.3V, and the reference should be 3.0V. Then, on C210, when no cartridge is connected, the SENSEA should be around 1.5 - 2V, far beyond the threshold of full ADC 1023 digits after the amplification.
@sparkybg

Yes, i have ADC 1013... :( you have list of component what should replacement? what is most important to working?

And this is normal when i connect C245 i have full power bar? and No instrument

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#TimeMemoryFunctionLocation
10.01762432824session_write_close ( )...(null):0
20.01792564400ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )...(null):0
30.01792565176Database_MySQL->query( ).../DatabaseHandler.php:119
40.06372703896Database_MySQL->error( ).../Db-mysql.class.php:273