Skip to main content ↑ ↓

Show Posts

This section allows you to view all Show Posts made by this member. Note that you can only see Show Posts made in areas you currently have access to.

Messages - mrjoda

1
Project logs / Re: Simple DIY JBC soldering station
hi, board is STM32F103C8T6 from ebay... I bought it and i must say : "it is piece of crap". Errata sheet is long as toilet paper. I spend a few days trying ADC manage to work but, no... simply no.... internal capacitor from AD integrator inject huuuuge amount of noise to ADC input (ADC1,ADC2, all channels !!! ) and it cause 1,6V offset (with 100k load on inputs drop to 0,6V). I2C is almost unusable. And so on... 

for me, bad choice
2
Open Bench Logic Sniffer / Re:
hi guys, i have same problem as author of topick and this dude https://www.youtube.com/watch?v=b4142knk5pk

after i bought it, i tried it and it wont work so i flashed new firmware, it tooks few hours because were problems with PIC flash. I flashed new Demon FW (now i cant flash older FW (errors)).

it doesnt work with any SW software (official, Jawis or PulseView) and i am really pissed of because i spend 67€ for not working crap.


can you help me please ?

thanks
6
Project logs / IR cable for FLUKE
Hi everyone

Here is one of my projects. Original Fluke cable is too expensive so i decided made one myself.

Circuit is basic connection of FTDI FT232RL with one LM393 at output/input powered from USB. I seen this schematic somewhere on internet but i dont have link.

PCB is little bit fancy. It has 13,7x23,20mm double sided.

The body of connector is 3D printed from PLA.

gerbers and steps are included down.
8
Project logs / Re: My HAKKO classic and T12/T15 soldering controller
[quote author="sparkybg"]

Hey are good enough for their price. And because original JBC is way better than original HAKKO, better get a JBC C245 instead. Or PACE TD100 - the tips are cheap - 11EUR per piece, more powerfull and more compact than HAKKO, but the iron handle is expensive - around 100EUR.

I am using C245 most of the time, and I am VERY happy with it.[/quote]


after a few weeks of using C245 i must say...last sentence is absolutely true... it is a absolutely brilliant handle, much much better than any HAKKO (maybe original the new one but it cost 4 times more)...

it worth any peny

you can see how fast is and how good is power transmission from handle to object here :

https://youtu.be/IMPuHNv7NsU

https://youtu.be/frqf3Z3nFx0
15
Project logs / Re: My HAKKO classic and T12/T15 soldering controller
i suspect the PIC is damaged, unfortunately only suplier is farnell, i go on vacation so when i come back i order and replace PIC. Meanwhile i drawn my own controller, this version is with MSP430F5310 but i work on stm32F051 version, is cheaper (2€ against 5€) and more powerfull and i can do direct phase regulation. It will be fun :)

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#TimeMemoryFunctionLocation
10.02132424560session_write_close ( )...(null):0
20.02182556136ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )...(null):0
30.02182556912Database_MySQL->query( ).../DatabaseHandler.php:119
40.06672695632Database_MySQL->error( ).../Db-mysql.class.php:273