Skip to main content ↑ ↓

Messages

This section allows you to view all Messages made by this member. Note that you can only see Messages made in areas you currently have access to.

Messages - sefee

2
Bus Pirate Development / Re: How to compile the v4+ firmware
I have not yet tried it with pirate loader
When I send the command i on the map, the LED Tx will Flash.
The MODE LED is off view that the dollar command does not work.
So to put me in BOOT mode I strap PGC and PGD with a jumper.

On the DS30 when I do a Check for blank the result is:
Searching for bl.
Found PIC24FJ64GA002 fw ver. 1.0.2

When I download BPv3-Firmware - v5.9RC - r556 - MPLABX.hex here is the result
Initiating download...
      Searching for bl.
      Found PIC24FJ64GA002 fw ver. 1.0.2
      Waiting for bootloader to be ready... ok
      Writing flash... ok
      Download finished
      Tx 51.2 kB  / Rx 301 bytes / 9.8s

Thanks
3
Bus Pirate Development / Re: How to compile the v4+ firmware
Hello
I changed my PIC.
I loaded the bootloader (BPv3-Bootloader - v4.4.hex) with pickit 3.
I loaded the firmware (BPv3-Firmware - v5.9RC - r556 - MPLABX.hex) with DS30 LOADER by turning the mode with a jumper on PGC and PGD because from my console I cannot configure it to put it in the programming of the firmware mode.
And I still can't a dialogue.
Is that I was not mistaken in the softs?
If someone has a solution because the I loses me.
Thanks in advance
4
Bus Pirate Development / Re: How to compile the v4+ firmware
Hello there,

I have a problem when I want to update my card Sparkfun V3.6.
I use DS30loader, and he said: The hex-file contains code That Will overwrite the bootloader.

Does anyone have a solution?

thank you in advance.
5
Bus Pirate Support / Re: Self test results
hello there,

I buy a card in "Hobby Electronics" (Bootloader V4.4 and Firmware V5.10) in May 2014 and when I pass the self-test it leaves me the error below, I need help to help me out because I can not find the scheme and implementation card.
I use the software:  LogicSniffer - Logic Analyser Client
My butts being to analyze the SPI link.
Thank you in advance for help from you would bring me.

Control
AUX OK
MODE LED OK
PULLUP H OK
PULLUP L OK
VREG OK
Analog pin and pwr supply
5V(0.0) OK
VPU(0.0) OK
3.3V(3.2) OK
ADC(3.2) OK
Bus normal, high
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z, low
MOSI OK
CLK OK
MISO OK
CS FAIL
Bus Hi-Z, high
MOSI OK
CLK OK
MISO OK
CS OK

Think you

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#TimeMemoryFunctionLocation
10.01232309360session_write_close ( )...(null):0
20.01262440960ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )...(null):0
30.01262441736Database_MySQL->query( ).../DatabaseHandler.php:119
40.05792580480Database_MySQL->error( ).../Db-mysql.class.php:273