Skip to main content ↑ ↓

Show Posts

This section allows you to view all Show Posts made by this member. Note that you can only see Show Posts made in areas you currently have access to.

Messages - sefee

2
Bus Pirate Development / Re: How to compile the v4+ firmware
I have not yet tried it with pirate loader
When I send the command i on the map, the LED Tx will Flash.
The MODE LED is off view that the dollar command does not work.
So to put me in BOOT mode I strap PGC and PGD with a jumper.

On the DS30 when I do a Check for blank the result is:
Searching for bl.
Found PIC24FJ64GA002 fw ver. 1.0.2

When I download BPv3-Firmware - v5.9RC - r556 - MPLABX.hex here is the result
Initiating download...
      Searching for bl.
      Found PIC24FJ64GA002 fw ver. 1.0.2
      Waiting for bootloader to be ready... ok
      Writing flash... ok
      Download finished
      Tx 51.2 kB  / Rx 301 bytes / 9.8s

Thanks
3
Bus Pirate Development / Re: How to compile the v4+ firmware
Hello
I changed my PIC.
I loaded the bootloader (BPv3-Bootloader - v4.4.hex) with pickit 3.
I loaded the firmware (BPv3-Firmware - v5.9RC - r556 - MPLABX.hex) with DS30 LOADER by turning the mode with a jumper on PGC and PGD because from my console I cannot configure it to put it in the programming of the firmware mode.
And I still can't a dialogue.
Is that I was not mistaken in the softs?
If someone has a solution because the I loses me.
Thanks in advance
4
Bus Pirate Development / Re: How to compile the v4+ firmware
Hello there,

I have a problem when I want to update my card Sparkfun V3.6.
I use DS30loader, and he said: The hex-file contains code That Will overwrite the bootloader.

Does anyone have a solution?

thank you in advance.
5
Bus Pirate Support / Re: Self test results
hello there,

I buy a card in "Hobby Electronics" (Bootloader V4.4 and Firmware V5.10) in May 2014 and when I pass the self-test it leaves me the error below, I need help to help me out because I can not find the scheme and implementation card.
I use the software:  LogicSniffer - Logic Analyser Client
My butts being to analyze the SPI link.
Thank you in advance for help from you would bring me.

Control
AUX OK
MODE LED OK
PULLUP H OK
PULLUP L OK
VREG OK
Analog pin and pwr supply
5V(0.0) OK
VPU(0.0) OK
3.3V(3.2) OK
ADC(3.2) OK
Bus normal, high
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z, low
MOSI OK
CLK OK
MISO OK
CS FAIL
Bus Hi-Z, high
MOSI OK
CLK OK
MISO OK
CS OK

Think you

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#TimeMemoryFunctionLocation
10.01272308752session_write_close ( )...(null):0
20.01312440328ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )...(null):0
30.01312441104Database_MySQL->query( ).../DatabaseHandler.php:119
40.05822579824Database_MySQL->error( ).../Db-mysql.class.php:273