31
USB Infrared Toy / Toy not available after reboot on RPi
Code: [Select]
OpenELEC:~ # dmesg
...
[ 13.043818] usb 1-1.2: device descriptor read/64, error -32
[ 13.090780] systemd-udevd[196]: starting version 214
[ 13.227193] usb 1-1.2: new full-speed USB device number 5 using dwc_otg
[ 13.403376] Console: switching to colour dummy device 80x30
[ 15.137466] pcm512x 1-004c: Failed to reset device: -5
[ 15.150748] pcm512x: probe of 1-004c failed with error -5
[ 15.215250] bcm2708-i2s bcm2708-i2s.0: Failed to create debugfs directory
[ 16.937918] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 16.939565] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.353850] usb 1-1.2: device descriptor read/64, error -32
[ 18.490409] input: lircd as /devices/virtual/input/input0
[ 18.573904] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 18.609968] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.537379] usb 1-1.2: device descriptor read/64, error -32
[ 23.720572] usb 1-1.2: new full-speed USB device number 6 using dwc_otg
[ 29.130120] usb 1-1.2: device not accepting address 6, error -32
[ 29.210534] usb 1-1.2: new full-speed USB device number 7 using dwc_otg
[ 34.617042] usb 1-1.2: device not accepting address 7, error -32
[ 34.617331] hub 1-1:1.0: unable to enumerate USB device on port 2
[ 34.697232] usb 1-1.3: new full-speed USB device number 8 using dwc_otg
[ 34.809228] usb 1-1.3: New USB device found, idVendor=2548, idProduct=1002
[ 34.809281] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 34.809300] usb 1-1.3: Product: USB-CEC Adapter
[ 34.809315] usb 1-1.3: Manufacturer: Pulse-Eight
[ 34.809331] usb 1-1.3: SerialNumber: v2 r8
[ 34.867145] input: Pulse-Eight USB-CEC Adapter as /devices/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3:1.2/0003:2548:1002.0001/input/input2
[ 34.875723] hid-generic 0003:2548:1002.0001: input,hidraw0: USB HID v1.10 Mouse [Pulse-Eight USB-CEC Adapter] on usb-bcm2708_usb-1.3/input2
[ 35.124791] cdc_acm 1-1.3:1.0: ttyACM0: USB ACM device
[ 35.141874] usbcore: registered new interface driver cdc_acm
[ 35.141918] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
I had to make a drastic snip in the dmesg log because the forum deemed it "too spamy".
The device will properly show up again when unplugging and reconnecting the Toy in this state.
I'm running firmware v22 on the USB IR Toy.
What can be the cause of the problem and how can I fix it?
Update 1: Even a fresh start-up of the RPi will not always properly initialize the Toy, resulting in the same problems as above.
Update 2: Forget the previous update. The Toy appeared to be completely dead, not functioning on any system any longer. It required me flashing the firmware again to get it up and running again. :-S