Skip to main content ↑ ↓

Show Posts

This section allows you to view all Show Posts made by this member. Note that you can only see Show Posts made in areas you currently have access to.

Messages - FantastIron2

2
Project logs / Re: Really universal soldering controller
Quote from: minkok on
You can make quick check if a driver of the Heater1 is ok by shorting colector - emiter of Q4 for not longer than 1s and check display temperature or by touching carefully the cartridge ( for T245, or irons using Heater1 ). If it heats, start to check if pulses comes to or comes out from the previous components until you reach pin of the controller. . . Simple!
P.s.  I would be also  disappointed if I got not working boards.
9
Project logs / Re: Really universal soldering controller
Quote from: sparkybg on
And I can confirm it is not. Just tried the latest bootloader with the latest firmware - my tips (3 original ones) start to melt 63/37 solder at 184-190 degrees. This is on both my original 5.2 board and my newest Tindie 5.2C board with capacitors removed.


Please upload a video of PC software while the C210 is warming up.

Quote from: sparkybg on
And I can confirm it is not. Just tried the latest bootloader with the latest firmware - my tips (3 original ones) start to melt 63/37 solder at 184-190 degrees. This is on both my original 5.2 board and my newest Tindie 5.2C board with capacitors removed.

Please upload a video of PC software while the C210 is warming up.

I flashed the newest bootloader/firmware ,but it dont work well yet. I cant upload to youtube, only can give some pics.
10
Project logs / Re: Really universal soldering controller
Quote from: sparkybg on
I will chek on p.1, but p.2 is not a problem. Any action on buttons or encoder takes it out of sleep mode, and this is intentional, and it has always been this way.

For p.1 - remove C85 and C86 on the back PCB if you installed them.
To proof it‘s a firmware problem ，I flashed the old firmware 2017，and it works well。So，I can confirm it’s firmware problem。
11
Project logs / Re: Really universal soldering controller
Quote from: sparkybg on
I will chek on p.1, but p.2 is not a problem. Any action on buttons or encoder takes it out of sleep mode, and this is intentional, and it has always been this way.

For p.1 - remove C85 and C86 on the back PCB if you installed them.
Thanks，for ur reply。
I tried 52and52c Backboard all，but  C210 still keep lower temperature。when I set T is 280 celsius，the Sn is solid status on the tip head。
12
Project logs / Re: Really universal soldering controller
@sparkybg  Hi，I just found two problems in the latest version firmware。
1. C210 the really temperature is very low than set temperature，about 100 celsius。
2. when iron in sleep mode，press any key it will go holder temperture。

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#TimeMemoryFunctionLocation
10.01642398848session_write_close ( )...(null):0
20.01682530424ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )...(null):0
30.01682531200Database_MySQL->query( ).../DatabaseHandler.php:119
40.06142669920Database_MySQL->error( ).../Db-mysql.class.php:273