Dangerous Prototypes Open Source Hardware

Is it possible to record a whole remote and export it as a LIRC config?

pi@raspberrypi ~ $ irrecord -n -H irtoy -d /dev/ttyACM0 RemoteXXX.conf

irrecord -  application for recording IR-codes for usage with lirc
Copyright (C) 1998,1999 Christoph Bartelmus(lirc@bartelmus.de)

This program will record the signals from your remote control
and create a config file for lircd.

A proper config file for lircd is maybe the most vital part of this
package, so you should invest some time to create a working config
file. Although I put a good deal of effort in this program it is often
not possible to automatically recognize all features of a remote
control. Often short-comings of the receiver hardware make it nearly
impossible. If you have problems to create a config file READ THE
DOCUMENTATION at https://sf.net/p/lirc-remotes/wiki

If there already is a remote control of the same brand available at
http://sf.net/p/lirc-remotes you might want to try using such a
remote as a template. The config files already contains all
parameters of the protocol used by remotes of a certain brand and
knowing these parameters makes the job of this program much
easier. There are also template files for the most common protocols
available. Templates can be downloaded using irdb-get(1). You use a
template file by providing the path of the file as a command line
parameter.

Please take the time to finish the file as described in
https://sourceforge.net/p/lirc-remotes/wiki/Checklist/ an send it
to  <lirc@bartelmus.de> so it can be made available to others.
Press RETURN to continue.

Checking for ambient light  creating too much disturbances.
Please don't press any buttons, just wait a few seconds...

No significant noise (received 0 bytes)

Enter name of remote (only ascii, no spaces) :Edifier
Using Edifier.lircd.conf as output filename

Now start pressing buttons on your remote control.

It is very important that you press many different buttons and hold them
down for approximately one second. Each button should generate at least one
dot but in no case more than ten dots of output.
Don't stop pressing buttons until two lines of dots (2x80) have been
generated.

Press RETURN now to start recording.
................................................................................
Got gap (108195 us) 
Please keep on pressing buttons like described above.
.........................................................................................................Gap not found, can't continue

Could not init hardware (lircd running ? --> close it, check permissions)

Press RETURN now to start recording.
................................................................................
Got gap (1000000 us) 
Please keep on pressing buttons like described above.
.....Signal too long
Creating config file in raw mode.

Please enter the name for the next button (press <ENTER> to finish recording)
VOLUME_UP
'VOLUME_UP' is not in name space (use --disable-namespace to override)
Press RETURN to continue.



Please enter the name for the next button (press <ENTER> to finish recording)
VOLUMEUP
'VOLUMEUP' is not in name space (use --disable-namespace to override)
Press RETURN to continue.

0001-Add-driver-for-USB-Infrared-Toy-in-sample-mode.patch.gz
0002-Add-USB-Infrared-Toy-driver-to-setup-system.patch.gz 

zcat PATCH_NAME_HERE | patch -p1

pi@raspberrypi ~/lirc-0.9.1 $ zcat 0001-Add-driver-for-USB-Infrared-Toy-in-sample-mode.patch.gz | patch -p1
patching file configure.ac
Hunk #1 FAILED at 154.
Hunk #2 succeeded at 458 (offset 13 lines).
Hunk #3 FAILED at 679.
Hunk #4 succeeded at 1403 (offset 13 lines).
2 out of 4 hunks FAILED -- saving rejects to file configure.ac.rej
patching file daemons/hw-types.c
patching file daemons/hw_usbirtoy.c
pi@raspberrypi ~/lirc-0.9.1 $ zcat 0002-Add-USB-Infrared-Toy-driver-to-setup-system.patch.gz | patch -p1
patching file setup.data
Hunk #1 FAILED at 119.
Hunk #2 succeeded at 147 with fuzz 2.
Hunk #3 succeeded at 191 with fuzz 2.
Hunk #4 succeeded at 394 with fuzz 2.
Hunk #5 FAILED at 432.
2 out of 5 hunks FAILED -- saving rejects to file setup.data.rej
patching file setup.sh
Hunk #2 succeeded at 211 with fuzz 2.
Hunk #3 succeeded at 375 with fuzz 2.