Skip to main content ↑ ↓

Show Posts

This section allows you to view all Show Posts made by this member. Note that you can only see Show Posts made in areas you currently have access to.

Messages - roboknight

1
Bus Pirate Development / Re: Bus Pirate v3 failed self test
I bought 10 regulators ($3+ ... just the shipping was a killer, $4 on $3... ugh).  The only thing I'm afraid of is that I replace the regulator and it goes again.  Hence the reason I was wondering if there was a better place to check.  I checked for a short and didn't see one.  Don't know how quickly it would burn if it did short, but... I didn't see any shorts.
3
Bus Pirate Development / Re: Bus Pirate v3 failed self test
I'm having a similar issue with the 5V failing, however, the 5V is just failing, connected to ADC or no.  I checked the regulator, and it does appear to have 5V coming in, but nothing coming out (at least, it doesn't appear so, since the PSU can't seem to be turned on).  Here is the output of W and i:
VREG too low, is there a short?
Power supplies OFF
DIO>i
Bus Pirate v3a
Firmware v5.10 (r559)  Bootloader v4.4
DEVID:0x0447 REVID:0x3046 (24FJ64GA002 B8)
http://dangerousprototypes.com
CFG1:0xFFDF CFG2:0xFF7F
*----------*
Pinstates:
1.(BR)  2.(RD)  3.(OR)  4.(YW)  5.(GN)  6.(BL)  7.(PU)  8.(GR)  9.(WT)  0.(Blk)
GND    3.3V    5.0V    ADC    VPU    AUX    CLK    MOSI    CS      MISO
P      P      P      I      I      I      I      I      I      I
GND    0.00V  0.00V  0.00V  0.00V  L      L      L      L      L
Power supplies OFF, Pull-up resistors OFF, Normal outputs (H=3.3v, L=GND)
MSB set: MOST sig bit first, Number of bits read/write: 8
a/A/@ controls AUX pin

*----------*

Now for the self-test:

Connect (Vpu to +5V) and (ADC to +3.3V)
Space to continue
Ctrl
AUX OK
MODE LED OK
PULLUP H OK
PULLUP L OK
VREG OK
ADC and supply
5V(0.47) FAIL
VPU(0.56) FAIL
3.3V(3.16) OK
ADC(3.23) OK
Bus high
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z 0
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z 1
MOSI OK
CLK OK
MISO OK
CS OK
MODE and VREG LEDs should be on!
Any key to exit

Mode and VREG lights are on.

The output of the voltage regulator appears to be 1.5... I'm guess, just a shot in the dark here, but that's not supposed to be 1.5 for a 5.0v regulator?  Anywhere else I can check for an issue (in case the regulator isn't the culprit)?  If the regulator does need replacing, you mention contacting the distributor for a replacement regulator.  I bought it here, but it looks like the board was supplied by SparkFun in my case?  So contact them?

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#TimeMemoryFunctionLocation
10.01192290552session_write_close ( )...(null):0
20.01222422128ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )...(null):0
30.01232422904Database_MySQL->query( ).../DatabaseHandler.php:119
40.05712561624Database_MySQL->error( ).../Db-mysql.class.php:273