Skip to main content ↑ ↓

Messages

This section allows you to view all Messages made by this member. Note that you can only see Messages made in areas you currently have access to.

Messages - gitdiy

2
Project logs / Re: Really universal soldering controller
Quote from: elkewerner on
I do not want your refund for U6 it cost only few pennys, if you tell me that it is faulty I can replace that, on my board U6 is fine. You already have all my info, I bought this board because SparkyBg said it is good and it gave him results as his board. If I knew that I am going to have all this hassle you think I would buy it? Please reply to the emails I have sent  if you cannot send me a New Working Board just do not reply and waste more of my time with SORRY, I already said your sorry is not accepted.
 
I hope you can believe me, I can definitely find the problem accurately, just replace the u6 chip
3
Project logs / Re: Really universal soldering controller
Quote from: tronix on
LOL @vulkan35.

I am thinking of unsubscribing since I cannot read without saying anything :o 

 >>>>Enlarging non-existent problems is incorrect!
Go tell that to the ppl we help here for the past 6 months with this 511 where were you besides doing profit selling Unisolder hundreds of sets on tindie.
1st Case reported of 511 goes back to January 2021 -- board bought from tindie.

I am happy to see you here facing this problem, help your customers and maybe solve it once for all, thanks.
Sorry, I have not followed the forum. The problem of 511 has only been known these days! I don't make a living mainly by selling unisolder. This is a personal hobby. As for profit, it is very transparent. I earned a small amount of manual fees, and I have other work to do!
4
Project logs / Re: Really universal soldering controller
Quote from: elkewerner on
You must be kiding me that you are going to refund U6 chip what about you give us the return address and send us a working one at your expense? I already replaced 5 chips on the device as suggest by vulkan35 which cost me €9.80 and still have 511c, I did the test as suggested on U6 and my drop voltage at 3V so I think U6 is fine but Q22, Q19 , D19 & D18  did not passed test after extracted. What about reply to my messages sorry is not enough for the time you wasted me.

Tell me your paypal, this problem is caused by u6, you have replaced the cost of other chips by mistake, I will return it to you
5
Project logs / Re: Really universal soldering controller
Quote from: elkewerner on
You must be kiding me that you are going to refund U6 chip what about you give us the return address and send us a working one at your expense? I already replaced 5 chips on the device as suggest by vulkan35 which cost me €9.80 and still have 511c, I did the test as suggested on U6 and my drop voltage at 3V so I think U6 is fine but Q22, Q19 , D19 & D18  did not passed test after extracted. What about reply to my messages sorry is not enough for the time you wasted me.

I have tested it and it can be solved by replacing u6
7
Project logs / Re: Really universal soldering controller
Unisolder has sold hundreds of sets on tindie, and a small part of them have encountered problems. Hand-made inevitably sometimes makes mistakes! Some friends in the forum said that 80% of the components are not original. What is the surface screen printing judgment? Personally think these statements are very absurd! 1% of chip problems will be 100% failures,
8
Project logs / Re: Really universal soldering controller
 tindie love diy, due to the replacement of the component supplier, the problem of the u6 chip REF3030 caused the c210 to process a 511 error! It can be solved by replacing REF3030. Friends who have the same problem can contact the seller to refund the chip fee. The seller only tested c245 when shipping, and the problem was not dealt with in time. I am very sorry about this!

( ! ) Fatal error: Uncaught exception 'Elk_Exception' with message 'Please try again. If you come back to this error screen, report the error to an administrator.' in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
( ! ) Elk_Exception: Please try again. If you come back to this error screen, report the error to an administrator. in /var/www/dangerousprototypes/forum/sources/database/Db-mysql.class.php on line 696
Call Stack
#TimeMemoryFunctionLocation
10.01532351368session_write_close ( )...(null):0
20.01562482968ElkArte\sources\subs\SessionHandler\DatabaseHandler->write( )...(null):0
30.01562483744Database_MySQL->query( ).../DatabaseHandler.php:119
40.06082622488Database_MySQL->error( ).../Db-mysql.class.php:273