This section allows you to view all Messages made by this member. Note that you can only see Messages made in areas you currently have access to.
Messages - talkos
" JBC C210 ",
(UINT16)(0.015 * 32768), //PID_KP
(UINT16)(0.008 * 32768), //PID_KI
picture for switching two windings of one relay
I will throw everything a little later;)
Why many people so bothered regarding display? Original 0.96" display is already good enough. It's perfectly visible unless you have the controller 2 meters away from you, which is a rare case solved by 1.3" display. Integrating more complex display, especially color ones, and a touch screen is A LOT of work almost for nothing. And there is already a plenty of work to do in the controller functionality. It's a tool. It's not a Christmas tree.
Channels are interleaved, and they should, as it's an universal controller supporting a variety of different tools, it needs to switch not only the power but also temperature sensor as only one amplifier for each temperature and current sense on the board. The power is limited anyway. So having two or three powerful tools will potentially limit the power of each other, since even idling tool consumes some of the power.
As Sparky said, it's better to just have a separate controller for each tool.
Как сказал Спарки, лучше иметь отдельный контроллер для каждого инструмента.
для процессора такой мощности как сейчас это абсолютно не напряг и портов для добавления инструмента достаточно и он же и является отдельным управляющим элементом для каждого инструмента тут всего то нужно немного допилить а нащот дисплея я думаю если у людей есть возможность и желание добавлять красоту в проект то мешать не стоит ибо( красота спасет мир) а сейчас сами понимаете время тяжелое
As Sparky said, it's best to have a separate controller for each tool.
for a processor of such power as it’s now, it’s absolutely not annoying and there are enough ports to add an instrument, and it is also a separate control element for each instrument; all that’s needed is to finish it a bit, and I think if the people have the opportunity and desire to add beauty to the project it’s not worth interfering because (beauty will save the world) and now you yourself understand the difficult time
Checked HW, FW, went through Sparkybg's notes - this will require new HW revision, which won't happen at least until summerколь пошла такая пьянка может стоит заменить дисплей на немного побольше и цветной как у нановерсии от jbc
since such a booze has gone, it may be worth replacing the display with a slightly larger and colored one like the jbc nanversion
Another question for those who understand the essence of the matter. We have a universal station with two channels, but we can only configure them to work in parallel like tweezers, and the question is, why not add the code a bit and make these channels work independently and then there will be something similar to the JBC but albeit without the possibility of a name together with tweezers and a soldering iron, or maybe even better to add at least one channel to the iron and then we can collect almost any configuration from two tools softly, this is true for the nano version, and of course it will not do without additional sleep channels for subs each tool
Thanks/Sposibo,everything is described in detail under my old YouTube video. https://youtu.be/C6gs7WieTSk
Can you share what Vacuum pump you used for de-soldering gun? de-soldering gun is in my TODO list for last 10 years, but never found powerful enough 12-24VDC pump. link to the pump itself where I can buy it would be best!
P.S if you want you can always write in English and at the end of the post write it in your native language I assume Russian.
P.S. I don't speak in Russian (my Russian dictionary in my brain only stores swearing words), but most of the time I understand what you mean if I have message both in English and in Russian.
Take care, mate!