USB and serial enabled LCD backpack design overview
From DP
Available for $16.95 at Seeed Studio.
Prototype PCBs are available in the free PCB drawer.
This is a USB and serial backpack for simple HD44780 character LCD screens. It has a few nice features that set it apart from the serial-only LCD backpacks at SparkFun and Adafruit:
- USB and serial control of characters LCDs
- Supported in common software (LCD Smartie) as 'matrix orbital' display
- Adjust contrast and backlight from software
- Couple extra pins for buttons
- 500mA fuse
- USB upgradable
Contents |
Overview
We wanted something that was like the serial only backpack that Adafruit and Spark Fun sell. But we wanted to make it USB too, and make it the same price with some extra features.
Hardware
Click for a full size schematic image. Schematic and PCB were designed with the freeware version of Cadsoft Eagle, download the latest project files from our Google Code project page.
Microcontroller section
The LCD Backpack uses a PIC18F2550 MCU (IC1), it is powered directly by USB 5v power supply trough a 500mA fuse (F1). The power supply is decoupled using a 0.1uF capacitor (C4), while the internal 3.3v USB power supply (VUSB) is decoupled using a 0.22uF capacitor (C3). The external clock is provided with a quartz crystal (Q1) and two capacitors (C1 and C2).
A ICSP programing header is provided and the MCLR pin is connected through a diode (D1) and a pull up 10K resistor (R1) to the power supply. This insures that the MCU is kept in reset until an adequate power supply is available. The diode stops any voltage feeding back into the pic power supply during high voltage programing.
Another part of it
PCB
We used the freeware version of Cadsoft Eagle to make the schematic and PCB. Download the latest designs and firmware from the project Google Code page.
- PCB and placement notes
- soldering advise
Partslist
| Part | Quantity | Value | Package |
|---|---|---|---|
| BACKLIGHT | 1 | 100R | B25P |
| C1,C2 | 2 | 27pf | C0805 |
| C3 | 1 | 220nF | C0805 |
| C4 | 1 | 0.1uF | C0805 |
| CONTRAST | 1 | 10K | B25P |
| D1 | 1 | BAS16J | SOD2514X100N |
| F1 | 1 | 500mA | RCL_L1812 |
| IC1 | 1 | PIC18F2550_28W | SO28W |
| ICSP | 1 | 1X05 | |
| J1 | 1 | USBSMD | USB-MINIB |
| LCD | 1 | 1X16 | |
| Q1 | 1 | 20MHz | HC49UP |
| R1 | 1 | 10k | R0805 |
| R2 | 1 | 1K | M0805 |
| RB4,RB5 | 2 | 1X01 | |
| SJ1 | 1 | SJ_2 | |
| T1 | 1 | BC818 | SOT23-BEC |
| UART,USB | 2 | 1X04 |
The latest sources and distributors are in the master partlist. See something missing? Please let us know.
Firmware
The firmware is written in C and compiled with the free Microchip C18 compiler. You can download the latest files from our Google Code project page.
- Operating modes
- extra software required
We used the Microchip USB stack to run the 18F2550 as a virtual serial port. Microchip's code is open but not redistributable. If you want to compile the source, download the stack from Microchip, then drag the source code into the install directory. See the detailed instructions in the PIC compiler how-to.
.inf installation
The virtual serial port (CDC) is an open standard, it should work on any modern operating system.
You don't need a driver, but you will need a .inf file to tell Windows how to use the device. A suitable .inf is included in the project archive.
Commands
The controller implements a (subset) of the serial interface provided by Matrix Orbital Serial LCDs.
To send a command, first send the START_COMMAND byte (0xFE), followed by the command (with any parameters), followed by the END_COMMAND byte (0x9A).
For example, to turn on the backlight, send 0xFE, 0x42, 0x00, 0x9A.
| Name | Decimal | Hex | Parameters |
|---|---|---|---|
| MATRIX_ORBITAL_COMMAND | 254 | 0xFE | None |
| BACKLIGHT_ON | 66 | 0x42 | 1 (minutes, 00=forever) |
| BACKLIGHT_OFF | 70 | 0x46 | None |
| CLEAR | 88 | 0x58 | None |
| HOME | 72 | 0x48 | None |
| POSITION | 71 | 0x47 | 2 (col, row) |
| UNDERLINE_CURSOR_ON | 74 | 0x4A | None |
| UNDERLINE_CURSOR_OFF | 75 | 0x4B | None |
| BLOCK_CURSOR_ON | 83 | 0x53 | None |
| BLOCK_CURSOR_OFF | 84 | 0x54 | None |
| BACKLIGHT_BRIGHTNESS | 152 | 0x98 | 1 (brightness) |
| CUSTOM_CHARACTER | 78 | 0x4E | 9 (character #, 8-byte bitmap) |
| NETWORK_CONFIG | 153 | 0x99 | None |
| END_COMMAND | 154 | 0x9A | None |
Bootloader
The LCD backpack can be upgraded over the USB connection. It uses a modified version of the Diolan USB PIC bootloader. This bootloader, written in ASM and released under the GPL, enumerates as an HID device. The bootloader app is included in the project archive.
Taking it further
Here's some ideas for the future:
- Enable and test software LCD contrast control. Solder jumper SJ1 near the contrast adjustment can be cut and resoldered so the PIC pulse-width modulator drives the LCD contrast. This should enable software control of contrast, but we have not yet tested it.
We'll post the most recent firmware updates on our blog. You can also join the discussion in the [forum].
Get one!
You can get one for $16.95.
Your purchases at Seeed Studio keep the open source project coming, we sincerely appreciate your support!