Bus Pirate Edu Kit Exercise no.11

From DP

Revision as of 14:35, 18 April 2013 by Arakis (Talk | contribs)
Jump to: navigation , search

Contents

Overview

BP EK E11 overview.jpg

The Circuit

BP EK E11 schematic.jpgBP EK E11 circuit.jpg

Breadboard legend

IC Location Breadboard wiring legend
IC PIN1 (+) PIN2 (-)
MCP7940M E14 E15
32KHz crystal C14 C15
C1 BB_-_left B14
C2 BB_-_left B15
Signal name Contact1 Contact2
5V BP_5V BB_+_left
5V BB_+_left BB_+_right
5V BB_+_right J14
5V BP_VPU BB_+_left
GND BP_GND BB_-_left
GND BB_-_left A17
MOSI BP_MOSI J17
CLK BP_CLK J16
  • The (+) and (-) next to PIN1 and PIN2 are intended for devices such as LEDs, where PIN1 should be the anode and connected to a higher potential then PIN2.

Bus Pirate Terminal


HiZ>m<<<
1. HiZ
2. 1-WIRE
3. UART
4. I2C
5. SPI
6. 2WIRE
7. 3WIRE
8. LCD
x. exit(without change)

(1)>4<<<
Set speed:
1. ~5KHz
2. ~50KHz
3. ~100KHz
4. ~400KHz

(1)>3<<<
Ready
I2C>P<<<
Pull-up resistors ON
Warning: no voltage on Vpullup pin
I2C>W<<<
POWER SUPPLIES ON



I2C>(1)<<<
Searching I2C address space. Found devices at:
0xDE(0x6F W)




I2C>[0xDE 0[0xDF r:9]<<<
I2C START BIT
WRITE: 0xDE ACK
WRITE: 0x00 ACK
I2C START BIT
WRITE: 0xDF ACK
READ: 0x00 ACK 0x00 ACK 0x00 ACK 0x01 ACK 0x01 ACK 0x01 ACK 0x01 ACK 0x80 ACK 0x00
NACK
I2C STOP BIT




I2C>[0xde 0 0x80]<<<
I2C START BIT
WRITE: 0xDE ACK
WRITE: 0x00 ACK
WRITE: 0x80 ACK
I2C STOP BIT



I2C>[0xde 0[0xdf r:9]<<<
I2C START BIT
WRITE: 0xDE ACK
WRITE: 0x00 ACK
I2C START BIT
WRITE: 0xDF ACK
READ: 0x82 ACK 0x00 ACK 0x00 ACK 0x21 ACK 0x01 ACK 0x01 ACK 0x01 ACK 0x80 ACK 0x00
NACK
I2C STOP BIT



I2C>[0xde 0[0xdf r:9]<<<
I2C START BIT
WRITE: 0xDE ACK
WRITE: 0x00 ACK
I2C START BIT
WRITE: 0xDF ACK
READ: 0xD4 ACK 0x01 ACK 0x00 ACK 0x21 ACK 0x01 ACK 0x01 ACK 0x01 ACK 0x80 ACK 0x00
NACK
I2C STOP BIT



I2C>m<<<
1. HiZ
2. 1-WIRE
3. UART
4. I2C
5. SPI
6. 2WIRE
7. 3WIRE
8. LCD
x. exit(without change)

(1)>1<<<
Ready
HiZ>

Not Working?

Taking it further