Search results

From DP

Jump to: navigation , search

Create the page "Power Supply" on this wiki!

Page title matches

Page text matches

  • Main Page
    ... outputs. [http://www.seeedstudio.com/depot/atx-breakout-board-bench-power-supply-p-1222.html?cPath=155 Available for $13.80].
    8 KB (1,083 words) - 22:29, 10 July 2016
  • Web Platform
    ...dware]] ([http://dangerousprototypes.com/2010/03/09/web-platform-usb-power-supply/ original])
    9 KB (1,155 words) - 03:32, 30 November 2016
  • Bus Pirate
    .../11/22/bus-pirate-high-voltage-power-supply/ Bus Pirate high voltage power supply] (PWM) ...//github.com/DangerousPrototypes/Bus_Pirate/tree/master/scripts/powertools Power tools]
    28 KB (3,622 words) - 18:26, 20 September 2016
  • HD44780 character LCD adapter
    HD44780 LCDs are generally 5volt parts with a separate supply for the back light. The [http://www.buspirate.com Bus Pirate] only has five ... LCD at 5volts. C1 (0.1uF) decouples the IC from fluctuations in the power supply.
    19 KB (2,934 words) - 14:16, 29 November 2012
  • Bus Pirate 101 tutorial
    ''1. Mini-B USB port.'' Connects the Bus Pirate to a PC. The Bus Pirate draws power from the USB port, and uses the data connection to communicate with the PC. ...wer indicator.'' This LED lights when the Bus Pirate is powered by the USB supply.
    9 KB (1,441 words) - 11:27, 19 December 2013
  • Bus Pirate self-test guide
    ADC and supply'''<u><<<analog pin test</u>''' ...n order to test their function, as well as verify the results of the power supply monitors.
    5 KB (894 words) - 10:07, 8 March 2018
  • Practical guide to Bus Pirate pull-up resistors
    The pull-up resistors aren't hard-wired to a power supply, you can apply any voltage level that's needed (from ground to +5volts). Ty ...'s 3.3volt or 5.0volt supply, be sure to use the 'W' command to enable the power supplies.
    3 KB (463 words) - 15:25, 15 November 2011
  • Introduction to dsPIC33 programming
    After power on and a few initialization operations, the microcontroller executes user c ...in state. A ‘1′ in the LAT register connects the pin to the chip power supply (3.3volts output), a ‘0′ connects it to ground (low). The next three l
    14 KB (2,265 words) - 10:21, 5 July 2016
  • 3EEPROM explorer board
    ...PROM] is a type of memory chip that stores data without a continuous power supply. It's useful for permanent data storage in small logger circuits, or holdin ...power parasitically from the 1-Wire bus, it doesn't have an external power supply pin and doesn't require a decoupling capacitor. IC2 and IC3 are empty spots
    28 KB (4,615 words) - 14:18, 31 August 2011
  • Bus Pirate menu options guide
    POWER SUPPLIES OFF ...s the Bus Pirate and immediately disables all pins, pull-up resistors, and power supplies.
    20 KB (3,493 words) - 15:56, 9 September 2016
  • IButton serial number
    ... the pull-up resistors on the 1-Wire data line, it doesn't need a separate supply. 1-WIRE&gt;W <span style="text-decoration: underline;">'''&lt;&lt;&lt;power supplies on'''</span>
    3 KB (496 words) - 05:54, 12 February 2011
  • 2AA02E48 EEPROM with MAC address
    *'''Power requirements:''' 3.3volts (1.7-5.5volts). ...C address pins or a write protect pin. The chip requires a 1.7-5volt power supply, we used 3.3volts.
    7 KB (1,121 words) - 05:54, 12 February 2011
  • Mixed voltage interfacing with the Bus Pirate
    ... be used to interface electronics above and below the Bus Pirate's 3.3volt supply. ...oard pull-up resistors, remember to connect the Vpullup pin to the circuit supply voltage. The Bus Pirate pull-up resistors are powered through the Vpullup p
    2 KB (336 words) - 00:55, 11 September 2010
  • Bus Pirate 102 tutorial
    ...Bus Pirate user interface and demonstrate some basic stuff like bus modes, power supplies, pull-up resistors, and number entry. Even if you've worked with t ===Power supplies===
    10 KB (1,672 words) - 13:09, 27 August 2012
  • DS1307 real time clock
    ...ing crystal. It also has a backup battery input so it can keep time during power failures. The battery backup also applies to 56byte of general purpose RAM. * '''Power requirements:''' 5volts (4.25-5.525volts).
    8 KB (1,324 words) - 05:55, 12 February 2011
  • Web platform hardware design
    The PIC requires a 0.1uF bypass capacitor on each power pin (C2,3,4), and a 10uF capacitor (C31) for an internal 2.5volt regulator ...s an internal 2.5volt regulator that requires a 10uF capacitor (C32). Each power pin also gets a 0.1uF decoupling capacitor (C5-8). The ENC28J60 can use up
    17 KB (2,684 words) - 03:28, 7 July 2016
  • Parallax RFID reader
    * '''Power requirements:''' 5 volts | Power
    3 KB (543 words) - 05:58, 12 February 2011
  • HMC6352 digital compass
    ... acquisition provides rapid heading updates, while query acquisitions save power by only measuring only when it's needed. * '''Power requirements:''' 2.7-5.2 volts.
    5 KB (782 words) - 05:58, 12 February 2011
  • Sure LED matrix
    * '''Power requirements:''' 5 volts. ...e controller at 5volts. Remember to connect the Vpu pin to the 5volt power supply.
    8 KB (1,302 words) - 05:57, 12 February 2011
  • AT45DB041D 4Mbit flash memory
    * '''Power requirements:''' 2.7-3.6volts. ...ator on the SUMP PUMP, but you could use the Bus Pirate's on-board 3.3volt supply if you've got a bare chip. For this demo, we connected the WP and RESET pin
    8 KB (1,320 words) - 05:57, 12 February 2011

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)