Linux, OSX (Python) firmware updates
Note: this page applies to the v2 'P24QP' bootloader. This bootloader is no longer used, please see the instructions for v2 to v4 upgrades.
Bus Pirate firmware updates can be done from Linux or OSX using the Python PIC24F programmer developed by broeggle and JoseJX. The programmer works on all operating systems that support Python and pySerial: Linux, OSX, and Windows, too. Thanks for a great script!
Our step-by-step guide to the Python PIC24F programmer continues after the break.
Here's some key stuff to get:
- The programmer works with Python 2.x, not 3.x.
- Get the pySerial module to give Python serial port access.
- Download the latest Python PIC24F programmer script. Future firmware releases (>2.0) will include the Python programmer script.
- Download the latest firmware. Copy the P24qp.ini configuration file and firmware .HEX to the same directory as the programmer script.
- Get a 0.1" jumper to place between the PGC and PGD pins, as described in the Windows quick programmer tutorial.
Install Python 2.x and the pySerial module. Download the firmware and programmer, move the required files into a convenient directory.
Disconnect the Bus Pirate from the USB cable (and power supply if applicable). Place a jumper between the PGC and PGD pins (A), as described in the Windows quick programmer tutorial. Plug the Bus Pirate back in.
C:\Python26>python P24qp.py Bus Pirate Programmer v1.0
P24qp <command> -a --auto=FILE - Erase, Program and Quit the Bootloader -c --config=FILE - P24qp compatible configuration file (Default: ./P24qp.ini) -e --erase - Erase the flash programming -f --finalize - Finalize the programming and go to user mode -i --info - Information about the bootloader -q --quiet - Quiet messages about writing progress -r --read=FILE - Read programming from flash -s --serial=DEVICE - Override serial device path -t --reset - Reset the bootloader -v - Enable verification of write commands -w --write=FILE - Write programming file to flash
Run the programmer from the command prompt for a short description of the flags and options.
JoseJX recommends auto mode with verify, using the command:
P24qp.py -a <hexfile> -s <serial port> -v
Substitute <hexfile> with the name of the firmware .HEX file, something like v25-Firmware-v2.hex for the Bus Pirate v2go. Replace <serial port> with the device name you system assigned to the Bus Pirate's FTDI USB->serial converter chip.
- Linux: /dev/ttyUSBx (/dev/ttyUSB0) or /dev/ttySx (/dev/ttyS1)
- OSX(?): /dev/cu.KeySerialx (/dev/cu.KeySerial1)
- Windows: COMx (COM3)
The serial port name can be tricky, hopefully these examples help. Replace 'x' with the number for your system. Look in the system dmesg to find the Bus Pirate on Linux, or in the control panel on Windows.
C:\Python26>python P24qp.py -a v25-Firmware-v2.hex -s COM5 -v Using Serial Port COM5 @ 115200 Reading 4 bytes from address 0x00FF0000 Found PIC24FJ64GA002 Erase Flash: Erasing 43 pages, starting at 0x00000000 Erase complete Writing 256 bytes to address 0x00000000 Reading 256 bytes from address 0x00000000 Verification failed at 0x00000000: 0 != 4 Verification failed at 0x00000001: 4 != 12 Writing 256 bytes to address 0x00000080 Reading 256 bytes from address 0x00000080 Writing 256 bytes to address 0x00000100 ...<<< This continues for awhile Reading 256 bytes from address 0x0000AA80 Writing 256 bytes to address 0x0000AB00 Reading 256 bytes from address 0x0000AB00 Writing 256 bytes to address 0x0000AB80 Reading 256 bytes from address 0x0000AB80 Verified Okay. Verification complete, switching to user mode
Ignore any verify errors at the beginning (0x0, 0x1) and between 0x400 and 0xbff, these are bootloader protected locations. A really nice thing about the Python programmer is that it knows to ignore errors in the protected bootloader section.